Big discounting Single layer Polypropylene fiber pleated low cost high efficiency pre-filter cartridge (HPP) series to America Factory
Big discounting Single layer Polypropylene fiber pleated low cost high efficiency pre-filter cartridge (HPP) series to America Factory Detail:
HPP series of cartridge adopt polypropylene melt blown membrane. Low cost and high efficiency, with high flux and long lifetime. Very good resistance of acid, alkali and chemical solvents. Widely used for pre-filtering in pharmaceutical, fine chemical and food&beverage.
Filtration of Acid and Alkali liquor;
Pre-filtration of chemical intermediate;
Pre-filtration of SVP and LVP;
Pre-filtration of biological products;
Pre-filtration of beverage and wine;
Prefiltration of freeze-dried powder;
Pre-filtration of high purity chemical reagent;
Cartridge filter of water treatment;
Pre-filtration of craft water;
Clarification of beverage&wine;
Good particles interception efficiency>=85%;
Excellent chemical stability;
High flux, high capacity pollutant, long lifetime;
85℃ hot water sterilization;
Filter media: Polypropylene melt blown membrane;
Diversion layer:Polypropylene fiber
Central tube: Polypropylene, strengthen heat resistance liner;
Shell/End cap: Polypropylene
Seal ring: Silicone rubber/EPDM/fluorous/outer terafluoroethylene rubber
Filter Area:≥0.60m2@ø69, 10”
A: normal Polypropylene shell and center tube,≤60℃
B: Polypropylene shell&socket liner,≤80℃
Max differential pressure: Positive pressure difference 4bar@23℃
Reverse pressure difference 2bar@23℃
|HPP Precision Up end Cap Length|
|0010=0.1um Z=Cylindrical sharp corner 25=2.5”|
|0022=0.22um S=Triangular fin 05=5”|
|0045=0.45um P=Bulkhead 10=10”|
|0065=0.65um LP=Two flat port 20=20”|
|0100=1.0um LHP=Two flat steel liner 30=30”|
|0800=8.0um PLP=One flat port one bulkhead 40=40”|
|2000=20.0um G=Heat resistance type|
|Central tube Down port Seal ring|
|Default=PP D=226 normal S=Silicone rubber|
|H=Stainless steel E=226 normal V=Fluorine rubber|
|T=Strengthen heat resistance liner DH=222 Outer steel ring Y=EPDM rubber|
|EH=226 Outer steel ring F=NBR|
|AD=222 special WV=Outer terafluoroethylene rubber|
|DN=220 Inner steel liner|
|EN=226 inner steel liner|
Product detail pictures:
Related Product Guide:
Water Filter Cartridge and Choosing the Right Water Filtration System
Basic Functions of a Water Filter Cartridge
We delight in an exceptionally good popularity amongst our customers for our fantastic product high quality, competitive cost as well as ideal service for Big discounting Single layer Polypropylene fiber pleated low cost high efficiency pre-filter cartridge (HPP) series to America Factory, The product will supply to all over the world, such as: Honduras , Poland , Netherlands , We seriously promise that we provide all the customers with the best quality products, the most competitive prices and the most prompt delivery. We hope to win a resplendent future for customers and ourselves.
Visit www.midsci.com or call 800-227-9997 to order some today for your lab!
TPP TubeSpins are ideal for the high throughput screening and optimization of suspension cell system process development. Each TubeSpin resembles a standard 50ml or 600ml conical tube, and the cap has a built-in 0.22µm hydrophobic membrane to maintain sterility and facilitate gas exchange. Process development and media optimization can be finely controlled by means of five cap holes of differing size that can be selectively sealed to achieve maximum cell yield and output.
The simple tube design contains no internal mixing or stirring mechanism which minimizes cell shearing and foam formation, and agitation is provided by shaking in a CO2 shaking incubator. In this manner, hundreds of cell cultivations can be performed quickly and efficiently in parallel.
More uses for your lab with the TubeSpins
Bacterial and Microbiological Cultures
TPP TubeSpins are ideally suited for the culture of bacteria, yeast, and other microbiological organisms in suspension. The simple, disposable format offers convenience and time-savings over traditional glass vessels such as test tubes which must be washed and autoclaved before each use. Both aerobic and anaerobic cultures can be grown by selectively covering the holes in the 0.22um filter cap. 10-35ml of culture can be grown in each TubeSpin, offering the flexibility to perform mini plasmid preps, small-scale candidate screens, or other downstream applications.
Ideal for Suspension
•Less incubator or hood space needed; when compared to a T75
•Less plastic usage and less plastic waste
•Great gas exchange throughout the culture
•No transfer stage — Spin down in the same tube
•Easier withdrawal from tube than a flask
The TPP TubeSpins are perfect for cell suspension. The cap is designed with 5 holes and a 0.22µm hydrophobic membrane. This allows for ideal gas exchange throughout your culture, and if needed, controlled gas exchange by covering the holes. By using the same vessel throughout each pass, less cells will be damaged or lost during a transfer.
The TubeSpin Bioreactors are great for our mini bacteria prep. We previously used regular conical tubes, unscrewed and taped the lids to the tube. However in our shaking incubator, the lids would invariably be jarred loose and our cultures would suffer. The TPP bioreactor tubes help us by saving us from taping the lids, and we are confident in the growth of our cells as well. — Miroslava Protic, Northwestern University, IL.
Order Number: TP87050
Description: 50ml TubeSpin Bioreactors
Order Number: TP87600
Description: 600ml TubeSpin Bioreactors
By Ivy from Paris - 2016.04.08 14:55
This is a reputable company, they have a high level of business management, good quality product and service, every cooperation is assured and delighted!
By Diego from Vietnam - 2016.08.18 11:04